| Server IP : 127.0.0.2 / Your IP : 18.116.28.60 Web Server : Apache/2.4.18 (Ubuntu) System : User : www-data ( ) PHP Version : 7.0.33-0ubuntu0.16.04.16 Disable Function : disk_free_space,disk_total_space,diskfreespace,dl,exec,fpaththru,getmyuid,getmypid,highlight_file,ignore_user_abord,leak,listen,link,opcache_get_configuration,opcache_get_status,passthru,pcntl_alarm,pcntl_fork,pcntl_waitpid,pcntl_wait,pcntl_wifexited,pcntl_wifstopped,pcntl_wifsignaled,pcntl_wexitstatus,pcntl_wtermsig,pcntl_wstopsig,pcntl_signal,pcntl_signal_dispatch,pcntl_get_last_error,pcntl_strerror,pcntl_sigprocmask,pcntl_sigwaitinfo,pcntl_sigtimedwait,pcntl_exec,pcntl_getpriority,pcntl_setpriority,php_uname,phpinfo,posix_ctermid,posix_getcwd,posix_getegid,posix_geteuid,posix_getgid,posix_getgrgid,posix_getgrnam,posix_getgroups,posix_getlogin,posix_getpgid,posix_getpgrp,posix_getpid,posix,_getppid,posix_getpwnam,posix_getpwuid,posix_getrlimit,posix_getsid,posix_getuid,posix_isatty,posix_kill,posix_mkfifo,posix_setegid,posix_seteuid,posix_setgid,posix_setpgid,posix_setsid,posix_setuid,posix_times,posix_ttyname,posix_uname,pclose,popen,proc_open,proc_close,proc_get_status,proc_nice,proc_terminate,shell_exec,source,show_source,system,virtual MySQL : OFF | cURL : ON | WGET : ON | Perl : ON | Python : ON | Sudo : ON | Pkexec : ON Directory : /etc/kbd/ |
Upload File : |
#
# This files tells the 'kbd' package:
#
# - whether to load a specific font and boot (and maybe a screen-font map,
# but you should avoid that if possible).
# - whether to setup an Application-Charset Map other than the default CP437.
# - whether to do screen saver/DPMS settings
# - whether to change the keyboard rate/delay or the state of the
# keyboard indicators
# - whether to show a clock
#
# You can also specify per-VC settings by suffixing variable names as in
# the examples below. This only works on framebuffer devices.
#
# For consistency with the configuration file of console-tools the
# following variables and their _vcN versions are also supported:
# SCREEN_FONT, SCREEN_FONT_MAP and APP_CHARSET_MAP.
#
#
# Example:
#
#CONSOLE_FONT=iso01.f16
#CONSOLE_FONT_vc2=LatArCyrHeb-16
#
#CONSOLE_MAP=iso05
#CONSOLE_MAP_vc2=user
#
# Set the following - more euro-friendly default than kernel font.
#CONSOLE_FONT=latarcyrheb-sun16.psf
# Forget this one unless you _know_ it is necessary for your font:
#FONT_MAP=iso01
# **** screen saver/DPMS settings: all VCs ****
# These settings are commented by default to avoid the chance of damage to
# very old monitors that don't support DPMS signalling.
# screen blanking timeout. monitor remains on, but the screen is cleared to
# range: 0-60 min (0==never) kernels I've looked at default to 10 minutes.
# (see linux/drivers/char/console.c)
# This is set to zero to avoid blanking the screen, because if a crash occurs
# it can conceal the output. On systems running with a graphical desktop, X
# is responsible for dpms settings, so this will not affect systems running
# graphically, and it makes more since for a non graphical system to not blank
# the screen automatically as most non graphical systems are headless unless
# a monitor has been attached for debugging
BLANK_TIME=0
# blanking method (VESA DPMS mode to use after BLANK_TIME, before powerdown):
# on: the default, no DPMS signalling. near instant powerup, no power saving
# vsync: DPMS Standby mode. nearly instant recovery, uses 110/120W (17" screen)
# hsync: DPMS Suspend mode. typically 3s recovery, uses 15/120W (17" screen)
# powerdown,off: DPMS Off mode, typ. 10s recovery, uses 5/120W (17" screen)
# Those values are for my 17" Mag, but some monitors do suspend the same as
# standby. xset dpms force {off|standby|suspend|on} is useful for this, if X
# supports DPMS on your video card. Set X's DPMS screensaver with xset dpms
# or use option power_saver in XF86Config
#
# DPMS set by default to on, because hsync can cause problems on certain
# hardware, such as Armada E500 laptops
BLANK_DPMS=off
# Powerdown time. The console will go to DPMS Off mode POWERDOWN_TIME
# minutes _after_ blanking. (POWERDOWN_TIME + BLANK_TIME after the last input)
POWERDOWN_TIME=30
# rate and delay can get only specific values, consult kbdrate(1) for help
#KEYBOARD_RATE="30"
#KEYBOARD_DELAY="250"
# Turn on numlock by default
#LEDS=+num
# Display a clock in the right upper corner of the console by running vcstime
#DO_VCSTIME=yes