| Server IP : 127.0.0.2 / Your IP : 3.138.202.226 Web Server : Apache/2.4.18 (Ubuntu) System : User : www-data ( ) PHP Version : 7.0.33-0ubuntu0.16.04.16 Disable Function : disk_free_space,disk_total_space,diskfreespace,dl,exec,fpaththru,getmyuid,getmypid,highlight_file,ignore_user_abord,leak,listen,link,opcache_get_configuration,opcache_get_status,passthru,pcntl_alarm,pcntl_fork,pcntl_waitpid,pcntl_wait,pcntl_wifexited,pcntl_wifstopped,pcntl_wifsignaled,pcntl_wexitstatus,pcntl_wtermsig,pcntl_wstopsig,pcntl_signal,pcntl_signal_dispatch,pcntl_get_last_error,pcntl_strerror,pcntl_sigprocmask,pcntl_sigwaitinfo,pcntl_sigtimedwait,pcntl_exec,pcntl_getpriority,pcntl_setpriority,php_uname,phpinfo,posix_ctermid,posix_getcwd,posix_getegid,posix_geteuid,posix_getgid,posix_getgrgid,posix_getgrnam,posix_getgroups,posix_getlogin,posix_getpgid,posix_getpgrp,posix_getpid,posix,_getppid,posix_getpwnam,posix_getpwuid,posix_getrlimit,posix_getsid,posix_getuid,posix_isatty,posix_kill,posix_mkfifo,posix_setegid,posix_seteuid,posix_setgid,posix_setpgid,posix_setsid,posix_setuid,posix_times,posix_ttyname,posix_uname,pclose,popen,proc_open,proc_close,proc_get_status,proc_nice,proc_terminate,shell_exec,source,show_source,system,virtual MySQL : OFF | cURL : ON | WGET : ON | Perl : ON | Python : ON | Sudo : ON | Pkexec : ON Directory : /usr/share/doc/libtxc-dxtn-s2tc0/ |
Upload File : |
S2TC Environment Variables
==========================
Color Distance Function
-----------------------
The following color distance functions can be selected by setting the
environment variable `S2TC_COLORDIST_MODE`:
* `RGB`: weighted YCbCr difference assuming linear input
* `YUV`: weighted Y'Cb'Cr' difference assuming sRGB input
* `SRGB`: weighted YCbCr difference assuming sRGB input
* `SRGB_MIXED`: weighted "Y'(Y)Cb'Cr'" difference assuming sRGB input
* `AVG`: standard average of component difference (generic)
* `WAVG`: weighted RGB average of component difference
* `NORMALMAP`: vector distance after normalization
The default is `WAVG`, which is a good compromise between speed and quality for
RGB and sRGB data. For optimum quality on sRGB input, try `SRGB_MIXED`.
The color distance function defines how "closeness" of pixel values is judged
when the pixel color values are evaluated, colors are selected, or during
refinement.
Color Selection
---------------
The environment variable `S2TC_RANDOM_COLORS` can be set the following way:
* `-1`: quick selection (darkest and brightest color are chosen, which is
similar to the method in the Color Cell Compression paper)
* `0`: all 16 input colors of a block are considered
* greater than `0`: additionally, that many random color values in the range
of the input color values are considered
The default is `-1`, which is fast but poor quality, however ideally suited for
online compression. For optimum quality, try `64`.
A bad color selection can later be compensated for by color refinement.
Color Refinement
----------------
The environment variable `S2TC_REFINE_COLORS` can be set to the following values:
* `NEVER`: never run color refinement
* `ALWAYS`: unconditionally perform color refinement
* `LOOP`: perform color refinement, evaluate its output and discard it if it
didn't improve quality, re-evaluate the pixel color values, and repeat
until no improvement could be made
The default is `ALWAYS`, which is fast and decent quality, and usually doesn't
make things worse. For optimum quality, try `LOOP`.
Color refinement recalculates the color palette of a block after the pixel
value decision by averaging the color values of those encoded as c0 or c1, and
is a technique that helps a lot of the initial color selection was poor (e.g.
if `S2TC_RANDOM_COLORS` was not set, or set to `-1`).